| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748 |
- Load "d:\\Z_AAA\\NA\\nation\\1\\uav_high_radar_n32g45x\\MDK-ARM\\Objects\\n32g45x_rtthread.axf"
- * JLink Info: Device "CORTEX-M4" selected.
- Set JLink Project File to "d:\Z_AAA\NA\nation\1\uav_high_radar_n32g45x\MDK-ARM\JLinkSettings.ini"* JLink Info: Device "CORTEX-M4" selected.
- JLink info:
- ------------
- DLL: V6.40 , compiled Oct 26 2018 15:06:02
- Firmware: J-Link V9 compiled Dec 8 2023 20:16:22
- Hardware: V9.70
- S/N : 602719622
- Feature(s) : GDB, RDI, FlashBP, FlashDL, JFlash
- * JLink Info: Found SW-DP with ID 0x2BA01477
- * JLink Info: Scanning AP map to find all available APs
- * JLink Info: AP[1]: Stopped AP scan as end of AP map has been reached
- * JLink Info: AP[0]: AHB-AP (IDR: 0x24770011)
- * JLink Info: Iterating through AP map to find AHB-AP to use
- * JLink Info: AP[0]: Core found
- * JLink Info: AP[0]: AHB-AP ROM base: 0xE00FF000
- * JLink Info: CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
- * JLink Info: Found Cortex-M4 r0p1, Little endian.
- * JLink Info: FPUnit: 6 code (BP) slots and 2 literal slots
- * JLink Info: CoreSight components:
- * JLink Info: ROMTbl[0] @ E00FF000
- * JLink Info: ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
- * JLink Info: ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
- * JLink Info: ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
- * JLink Info: ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
- * JLink Info: ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
- * JLink Info: ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
- ROMTableAddr = 0xE00FF000
- * JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
- * JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.
- Target info:
- ------------
- Device: N32G455CCL7
- VTarget = 3.290V
- State of Pins: TCK: 0, TDI: 0, TDO: 0, TMS: 1, TRES: 1, TRST: 1
- Hardware-Breakpoints: 6
- Software-Breakpoints: 8192
- Watchpoints: 4
- JTAG speed: 3000 kHz
- Erase Done.Programming Done.Verify OK.* JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
- * JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.
- Application running ...
- Flash Load finished at 13:12:55
|
